When I’m on the shop floor, walking past a machine where a metalworker’s slapping a flap disc onto an angle grinder to knock down weld beads or rough out a cast iron part, I hear the same question every time: “Which grit size of flap disc is best for rough grinding?” As a flap disc supplier who’s spent 12 years standing right next to those machines—answering that question, testing discs in our own lab, and troubleshooting for guys who’ve been grinding long enough to know a good disc from a bad one—I can tell you it’s not a one-size-fits-all answer. A lot of guys grab the coarsest grit they can find, assuming it’ll move material faster, but that’s a rookie move that leads to burnt metal, wasted discs, and sore wrists. Let’s break this down with real shop science, not the glossy marketing brochures that say every disc is “the toughest on the market.” Flap Disc

First, let’s get clear on what rough grinding actually is. Rough grinding isn’t precision work; it’s the first step: removing excess weld seam, grinding down cast iron flash, trimming laser-cut edge burrs, or cleaning heavy rust off a thick steel plate. The goal here is speed of material removal, not a perfect finish. Grit size is measured by the number of abrasive particles per square inch of the disc’s backing. Lower numbers mean larger, coarser particles—so 36-grit has fewer, bigger grains than 60-grit, which has more, smaller ones. That’s the basic math, but there’s way more to it than just numbers.
I’ll walk you through the grit ranges we actually sell and test, starting with the workhorses for rough jobs. Our 36-grit flap disc is the first call for most rough grinding tasks. I’ve seen it take a 1/8-inch weld bead off a 1-inch thick steel plate in 10 seconds flat, no problem. But before you run out and grab 36 for every rough job, you have to match it to the material and the machine you’re using. For thick carbon steel, stainless steel welds on structural beams, cast iron, and heavy-duty rust removal, 36 is unbeatable. Why? Coarser particles have more surface area to dig into the metal, so they bite harder. But here’s the catch: 36-grit will also remove material unevenly if you’re not holding the grinder right, and it’s way more aggressive on thin materials. If you’re grinding 16-gauge sheet metal, 36 will chew through it so fast you’ll have a hole before you finish your first pass. I learned that the hard way early on—gave a guy a 36-grit disc for grinding welds on 14-gauge handrails, and he came back 20 minutes later swearing the disc was defective. Turned out he was pressing down like he was splitting wood, and the metal was too thin for that kind of force.
Next up, 40-grit. A lot of guys ask me if 40 is just a “watered-down” 36, and honestly, it’s not—it’s a middle ground that’s perfect for a huge swath of rough grinding jobs where 36 is too aggressive and 60 is too slow. I sell more 40-grit flap discs than any other size, because it’s versatile. If you’re doing light structural work, like removing tack welds on a 1/4-inch steel bracket, cleaning up mill scale off a medium-thickness plate, or grinding out small, shallow welds on pipe, 40 hits that sweet spot. It’s aggressive enough to move material fast, but it’s more consistent than 36—it doesn’t dig into the metal as deep, so you get a flatter base for your next finishing step. I had a regular customer, a pipe fitter named Joe, switch from 36 to 40 two years ago, and he told me he went through 20 fewer discs a month because he wasn’t burning through the edges of the disc on every pipe joint. That’s the real-world data you won’t find in a spec sheet.
Now, why you should skip anything coarser than 36-grit for rough grinding. We used to stock 24-grit flap discs years ago, and we barely sell any now. 24-grit particles are so large that they’re prone to tearing out of the disc’s backing way faster than 36, even though they look like they’d move more material. The bond that holds the abrasive grains onto the fiber or fiberglass backing has to be strong enough to keep the grains in place, and 24-grit’s big grains put way more stress on that bond. I tested a 24-grit vs. a 36-grit on the same 1-inch thick steel plate last quarter: the 24-grit removed 10% more material, but it wore out 45% faster, so net, it was way less efficient. Guys think “coarser = faster,” but that’s only true if the disc lasts long enough to get the job done. 24-grit is only useful for super heavy, low-prep work, like cleaning up a pile of scrap metal before recycling, not for any job that requires consistent results.
Then there’s the mistake a lot of guys make when they’re choosing grit: confusing rough grinding with stock removal. Wait, no—rough grinding is a type of stock removal, but stock removal is a broader term that includes things like sanding down a full plate. Here’s the difference: rough grinding is about removing specific, heavy defects (welds, flash, rust), while stock removal might mean taking off a uniform layer of metal. For stock removal on heavy material, 36 or 40 is still great, but if you’re working with stainless steel, you have to adjust. Stainless is a soft, gummy metal that clogs abrasive grains way faster than carbon steel. I always tell guys working on stainless to go a little coarser than they would for carbon, but not too much. 36-grit works, but sometimes 40 lasts longer because the smaller (still coarse) grains don’t clog as quickly as 36’s larger grains, which fill with stainless gunk right when they start to dig. We did a side-by-side test on a stainless steel weld last month: a 36-grit disc clogged halfway through the weld, and the 40-grit kept going 20% longer. That’s a key point most suppliers don’t mention—grain size’s performance changes with the material you’re grinding.
Another factor no one talks about: the type of flap disc you’re using, not just the grit. A lot of guys buy a cheap flap disc that has glued-on flaps instead of fused, and even if it’s the right grit, it’ll fall apart mid-job. But when we’re talking about rough grinding with the right grit, the two most common types are fiberglass-backed flap discs (for angle grinders, the most common tool) and high-density flap discs for heavy-duty grinders. For the average DIYer or small shop using a 4.5-inch angle grinder, 36 or 40 grit is perfect. For a big fab shop using 7-inch grinders for heavy structural work, 36 grit is the way to go, but you need a disc with a heavy fiberglass backing that can handle the torque without warping. I’ve had guys come to me saying they burned through three discs in an hour on heavy cast iron, and it wasn’t the grit—it was the cheap, paper-backed discs they were buying. The backing matters just as much as the grit when you’re grinding aggressively.
Wait, let’s address a common myth: “Finer grits can’t be used for rough grinding.” I get asked this all the time, and yeah, technically you could use 50 or 60 grit, but it’s not efficient. 60 grit has way smaller particles, so each particle removes less material. You’d have to spend twice as long grinding, and you’d burn the metal because you’re applying too much pressure. I saw a guy try to use 60 grit to grind a 1/2-inch weld once, and he ended up taking 15 minutes instead of 2, and the weld was still lumpy. Finer grits are for finishing, not rough work. The sweet spot for rough grinding is between 36 and 40 grit, with 36 for the heaviest jobs and 40 for the middle-of-the-road work.
Now, let’s talk about how to use that grit correctly, because even the best disc won’t work if you’re using it wrong. First, don’t press down hard. A lot of guys think more pressure = faster material removal, but it just forces the abrasive grains into the metal too deep, making them break instead of cutting. The grinder’s weight is enough—let the disc do the work. Second, move the grinder in a consistent, side-to-side motion, not just up and down, to prevent uneven grinding. And when you finish the rough grinding, don’t jump straight to a fine grit without cleaning the metal first? Wait, no—actually, the rough grit leaves a very coarse scratch pattern, so you’ll need at least one step of medium grit (like 80) before finishing, but that’s beyond the question of which grit is best for rough grinding.
I’ve spent 12 years testing flap discs in our own test lab, running side-by-side comparisons with every major brand, and here’s what I can tell you from real data: for heavy rough grinding on carbon steel, cast iron, or thick structural steel, 36-grit is the most efficient. For general rough grinding—tack welds, mill scale, light rust, medium welds—40-grit is the best balance of speed, disc life, and finished quality. 24-grit is a waste for anything beyond scrap prep, and anything finer than 50 is just too slow for rough work.

If you’re still unsure which grit is right for your job, or you’ve been burning through discs too fast on your rough grinding tasks, I’m here to help. We don’t sell cheap discs that fall apart after 5 minutes; our flap discs are tested to handle the rough work you do, and we can help you pick the right grit and style for your specific material and tool. Reach out to our team to discuss your project, and we’ll make sure you get the right disc for the job.
Strip Disc References:
- Abrasive Technology Association. (2022). Selecting Flap Discs for Surface Preparation and Stock Removal.
- Metalworking Trade Journal. (2021). Real-World Performance of Coarse Grit Abrasive Discs on Structural Steel.
- National Institute for Occupational Safety and Health. (2020. Workplace Safety Guidelines for Angle Grinder Operation and Abrasive Disc Selection).
Zhenjiang Cutech Tools Co., Ltd.
Zhenjiang Cutech Tools Co., Ltd. is one of the most professional flap disc manufacturers and suppliers in China, also supports customized service with low price. Please feel free to wholesale CE approved flap disc made in China here from our factory. Welcome to contact us for pricelist and quotation.
Address: NO.66 Runxing Road, Runzhou Private Economy Development Zone, Zhenjiang, China.
E-mail: cutechtool@gmail.com
WebSite: https://www.cutech-tool.com/